EA9 Finish HB is a two-pack amine-adduct cured epoxy specially developed to achieve long-term corrosion protection for many types of surfaces i.e. aluminium, galvanising, steel and concrete. This feature combined with its wide range of resistance properties make EA9 Finish HB a durable, high performance and economical coating for immersion as well as non-immersion services. EA9 Finish HB system has been extensively used for long-term corrosion protection lining of a storage tank for palm oil derivatives, vegetable oil, potable water etc. Product Features: • Good resistance to abrasion and mechanical damage • Excellent on correctly prepared surfaces • Outstanding resistance to aqueous solutions and a wide range of industrial chemicals • Dry service temperature range up to 100C read more

A high performance, high solids, two-pack epoxy mastic designed to provide corrosion resistance and abrasion protection in extreme service applications. This specially designed epoxy system is capable of being applied as a one or two coat system over grit blasted, hydroblasted or mechanically cleaned surfaces. It can be applied and cures underwater to form a tough protective barrier. It provides outstanding adhesion on wet blasted surfaces. Is designed to provide corrosion protection for metal and concrete structures onshore and in offshore marine and petrochemical services, sheet piles, underground and submarine pipes, waste water tanks, jetty piles, underground tanks and other structural steel that requires protection against corrosion in aggressive environments. It is most suitable for rehabilitation of corroded steel and concrete structures in tidal zones and below the water line where conventional protective coatings are not applicable. It is an ideal maintenance product for cold pipes with condensation. read more

Penguard Express Penguard Express is a fast drying, high-build, high-solids epoxy coating. Penguard Express is specially designed for new construction and can be used as a primer, midcoat, finish coat or as a single-coat system in atmospheric conditions. Penguard Express has very fast dry-to-recoat or dry-to-handle properties. It has a wide application temperature range from -5C to 40C. Penguard Express is suitable to use on properly prepared carbon steel, aluminium, concrete and galvanised steel substrates. It can be applied at sub-zero surface temperatures. Penguard Express is approved for NORSOK system 1 and is suitable for application up to C5 environment. Key features Fast dry-to-recoat Fast dry-to-handle Wide application temperature range Designed for new construction Technical details Product Categories Anticorrosive primersBuilding - exteriorBuilding - interiorNew construction primersExterior steel protection coatings - buildings Interior steel protection coatings - buildings Penguard Express ZP Penguard Express ZP is a fast-drying and high-build epoxy coating pigmented with active zinc phosphate. Penguard Express ZP is specially designed for new construction, is a high-solids product and can be used as a primer, midcoat, finish coat or as a single-coat system in atmospheric conditions. Penguard Express ZP is pigmented with active zinc phosphate for increased corrosion protection, and has very fast dry-to-recoat or dry-to-handle properties. Penguard Express ZP is suitable to use on properly prepared carbon steel, aluminium, concrete and galvanised steel substrates. It can be applied at sub-zero surface temperatures. Penguard Express ZP is suitable for application up to C5 environment. Key features Pigmented with active zinc phosphate Fast dry-to-recoat Fast dry-to-handle Designed for new construction Technical details Product Categories Anticorrosive primersNew construction primers Technology Epoxy Substrate Carbon steelCoated surfaces Shop primed steel ​ ​ Penguard Express MIO Penguard Express MIO is a fast-drying and high-build epoxy coating enforced with MIO. Penguard Express MIO is specially designed for new construction, is a high-solid product and can be used as a primer, midcoat, finish coat or as a single-coat system in atmospheric conditions. Penguard Express MIO is enforced with micaceous iron-oxide pigments for increased barrier effect, and has very fast dry-to-recoat or dry-to-handle properties. Penguard Express MIO is suitable to use on properly prepared carbon steel, aluminium, concrete and galvanised steel substrates. It can be applied at sub-zero surface temperatures. Penguard Express MIO is suitable for application up to C5 environment. Key features Enforced with Micaceous Iron Oxide (MIO) Fast dry-to-recoat Fast dry-to-handle Designed for new construction Technical details Product Categories Anticorrosive primersNew construction primers Technology Epoxy Substrate Carbon steelGalvanized steelConcreteCoated surfacesShop primed steel     read more

Jotamastic Smart Pack Jotamastic Smart Pack is a surface-tolerant epoxy mastic primer designed for maintenance and repair with brush and roller. It is specially designed for areas where optimal surface preparation is not possible or required. Jotamastic Smart Pack has a superior flow, ensuring a consistent protective film with correct thickness with brush and roller application. The 1:1 mixing ratio allows you to only mix the amount needed, reducing waste and cost.   Key features Made for brush and roller 1:1 easy mixing Saves time and money Surface-tolerant Easy to achieve smooth film build Technical details Product Categories Anticorrosive primersMaintenance primers Technology Epoxy mastic Substrate Carbon steelGalvanized steelStainless steelConcreteCoated surfaces read more

Jotun Tankguard Storage Getting your clean petroleum product and crude oil tanks back into service withing 24 hours. Jotun Tankguard Storage is a two-pack, high solid phenolic epoxy coating highly resistant to a wide range of chemicals and solvents.   Jotun Tankguard Plus Tankguard Plus is a two component novolac epoxy tank coating. This is a two component polyamine cured phenolic/novolac epoxy coating. It has a high resistance to most sour crude oils and a wide range of chemicals and solvents. It has outstanding chemical resistance to crude oil at temperatures up to 160 °C. Can be used as primer, mid coat or finish coat in atmospheric and immersed environments. Suitable for properly prepared carbon steel, galvanised steel, stainless steel and concrete substrates. Approvals and certificates In compliance with Federal Drug Authority, USA, FDA Title 21, Part 175.300, approved for exposure to dry and liquid foods Colours buff, white Typical use Protective: Specially designed as an internal lining for offshore, onshore and buried tanks and pipes such as chemical storage, waste water, grey water, process water, concrete bund, fire service lines and drilling mud tanks. This coating has very good resistance to high temperature products. Refer to Protective Product Resistance List. Tankguard 412 is a two-component solvent-free tank lining with good chemical resistance. It is suitable for marine purposes as a coating for potable water, grey water and crude-oil tanks. Tankguard 412 is recommended as a lining onshore and offshore, and for buried tanks and pipes. It can be used as a primer, a midcoat or finish coat in atmospheric and immersed environments. This product is suitable for properly prepared carbon steel, galvanised steel, stainless steel and concrete substrates.For chemical resistance information please refer to the Jotun Protective Resistance List.  Key features Tank lining with good chemical resistance Approved for potable water Tankguard SF Tankguard SF is a solvent-free tank lining with the possibility for wet-on-wet application – making it the fastest back-to-service novolac tank lining. Tankguard SF has good resistance to a wide range of chemicals, such as crude oil up to 140°C and clean petroleum products. It also has very good resistance to inorganic acids. It can be applied in film thickness down to 150 µm and up to 500 µm.   Key features High chemical resistance  Sour crude-oil resistant up to 140°C  Wet-on-wet application possible  Solvent free novolac with a wide DFT range (150-500 µm) read more

Hardtop AX is a polyurethane topcoat with a robust finish, a good glossy finish that lasts and low VOC. Its robust finish with strong mechanical properties, very good chemical resistance and a low dirt pick up – combined with very good colour – and gloss retention – ensures a glossy finish that lasts. Hardtop AX has high sag resistance, will give minimal spray dust and cures at low temperatures – making it easy to achieve a smooth finish and good result. It has very good application properties by airless spray, brush and roller, making it very user friendly. The products do not contain solvents defined as hazardous air pollutants (HAPs). Hardtop AX can be used for topsides, decks, superstructures on ships, in offshore environments, refineries, power plants, bridges, buildings and for other industrial uses. Minor amounts of solvents may come in through tinting in some colours. Key features Robust finish Easy application Superior durability Very good chemical resistance Low VOC Technical details Product Categories TopcoatsBuilding - exteriorArchitectural topcoatsIndustrial topcoatsExterior steel protection coatings - buildings Technology Polyurethane Substrate Coated surfaces MCI TintableYes Certificates and Approvals   APAS approved to specification 2911 When used as part of an approved scheme, this material has the following certification: - Low Flame Spread in accordance with EU Directive for Marine Equipment. Approved in accordance with parts 5 and 2 of Annex 1 of IMO 2010 FTP Code, or Parts 5 and 2 of Annex 1 of IMO FTPC when in compliance with IMO 2010 FTP Code Ch. 8 This product contributes to Green Building Standard credits by meeting the following specific requirements: BREEAM® NOR (2016) - Hea 02: VOC content for Two-pack performance Coatings SB (500 g/l) (EU Directive 2004/42/CE) and emission demands (ISO 16000-series). - Mat 01: The product Safety Data Sheet confirms that the product does not contain any substances on the Norwegian A20 list. BREEAM® NOR (2012) - Hea 9: VOC content for Two-pack performance Coatings SB (500 g/l) (EU Directive 2004/42/CE) and emission demands (ISO 16000-series). - Mat 1.5: This product Safety Data Sheet confirms that the product does not contain any substances on the Norwegian A20 list.   For more detailed and specific information about the standards, certificates and other documentation please see TDS or contact your local Jotun representative read more